Home > Hard Drive > OS Not Loading On New SATA Drive

OS Not Loading On New SATA Drive


I spent about six hours on this silly thing before I found this bit of advice. Another suggestion is to replace the DVD drive with second HD cause no one uses it anyway. I also sprayed some connector sprayto make sure there was no problem with erosion on the pins or hard drive. 08/12/2015 by asle Can you clarify what you mean by "put I am stumped as to how to get this going. this content

So i took it out tried all SATA ports, tried all power supplies. Then, burn the iso file to CD/DVD or USB flash drive. On the other hand, if you set these new drives' port modes to AHCI or Native SATA, Windows cannot communicate with them. Report Sujit- Apr 11, 2010 at 03:05 AM Thanks boss, I was about to return the HDD as I thought it has some problems, but followed ur instruction, and I succeeded.

Second Hard Drive Not Showing Up In Disk Management

Drive is recognized correctly in bios, is listed correctly as a HDD in device manager, but is not found in disk management. I am in the same boat & can see the slave in disk manager as local disk but only option is to format it in actions etc I dont want to I am currently running a Maxtor 200GB SATA drive as the master and a Maxtor 120GB IDE drive as the slave. Then check whether a CD comes with the drive, providing drive-specific information and general upgrade assistance.

I don't know if this still is a requirement, but you could try it. Now all solutions to “hard disk not detected during Windows installation” have been introduced, and you can try one or some of them when you are having the same problem. Everything works with my SSD alone but nothing works with my HDD attached.. Second Hard Drive Not Showing Windows 7 I have a similar issue in that my PSU is fine with 3 HDDs on one SATA power cable, but won't boot if I use the 4th connector.

Find out who represents you in Minnesota's legislatures. I've tried Using SeaTools and It only reads the functioning drive that is already installed, I tried booting with a Vista install disk to see if It can at least notice Error 2.No drives were found. http://www.pcworld.com/article/2360427/what-to-do-when-a-second-hard-drive-bricks-your-pc.html That step MUST be done before you can Format the Partition.

Yes No Voted Undo Score 9 Cancel Comments: good answer + 11/16/2010 by rj713 Thank you for your help. How To Install Seagate Hard Drive On Pc Next, boot the computer from MiniTool Partition Wizard Boot Disk, and use its "Delete All Partitions" feature to clean the target disk. Finally became smart and reworded my google search "installing second sata hard drive without raid" and this was the first link that google came up with. I hooked the 750GB up to the MacBook through an external USB - SATA interface.

How To Connect Sata Hard Drive To Motherboard

When all the choices are made, go ahead with the Partition operation.When that is done, come back to this new Partition and RIGHT-click again and choose to Format it. http://www.tomshardware.com/answers/id-1664309/boot-installing-sata-hard-disk.html Had me baffled for a while as I am only used to Ide Drives. Second Hard Drive Not Showing Up In Disk Management I have three SATA drives installed just fine -- two Seagates and a Maxtor. Install Seagate External Hard Drive BUT you did not say that your next step was to Create a new Primary Partition on that HDD unit.

aeternum91Feb 15, 2014, 5:31 AM I swapped the SATA cables around and even tested them with both SATA 2 and 3. news defective drive Try the drive in 1. When your stuff breaks, they want to be the only people allowed to fix it. Please note, the second HDD did not contain any OS, and I was using it for storage of excess data only.Recently, I tried booting the system and like you I faced Second Hard Drive Not Showing Windows 10

The lower one also shows you the hardware Windows can see, including some devices Windows does not yet understand. Choose the NTFS File System option. This was at least required on the old disks before SATA came along. http://gamesversion.com/hard-drive/old-sata-hd.php Report Ben- May 8, 2010 at 10:45 AM thanks you for your explanation, is clear and easy to understand for newbie like me Report ali- Jun 7, 2010 at 01:34 PM

Win XP does not have built-in drivers for "native Sata" or AHCI devices. How To Install A Hard Drive In A Laptop make the division between DATA AND POWER on the tape and plug into ribbon cable. However I have cloned this new disc using Diskcopy 2.3 ( non windows cloning tool) with XP from another that is recognised when it was in Windows.

You can either change their port modes or, much better yet, you can install into Win XP the driver for AHCI devices so that it CAN use these units.

Ask us. Note that some older PCs use 40-conductor IDE cables, not the 80-conductor ones current drives require. (Compare your kit cable to the one installed—the 80-conductor variety has much thinner wires.) 80-conductor You said, "I also have a 1 tera byte Hitachi hard drive that is seen on the initial boot up screen, but not in windows at all. "We'll need a little Install New Hard Drive Windows 7 Manufacturers don’t want a Fair Repair bill.

By that you can protect yourself if the problem shows up again in the future. 09/09/2016 by Dimitri Sakian Try ELECTRICAL tape around all of the hard drive cable! Report Marsun- Oct 7, 2009 at 05:34 PM I am having the same problem, I do not get the "format" option with the right click. Now exit out of disk Management and reboot so Windows can put this into into its Registry, and you should find the disk in My Computer again.Whatever you find, post back check my blog Some older systems may see the drive and classify it as a SCSI device if you are using a Serial ATA host adapter.